Talking about the use of the wire take-up frame of the CNC winding device

The structure of the pay-off frame of the pay-off frame is shown in the figure. Among them, three fixing screws of the base are uniformly distributed on the circumference of the bottom panel of the wooden core, and the lead frame is welded with the rotatable shape. Use the method to place the round core of the wire on the base, make the shaft pass through the hole of the core, and adjust the three fixing screws on the base so that the wood core is basically centered and then the fixing screws are locked to fix the wood core.

Install the lead frame and tighten the nut on the bolt. Adjust the set screw so that the crossbar of the lead frame is substantially parallel to the upper end panel of the wood core, and then lock the nut on the bolt. Pull out the wire end of the wire, pass through the two wire sleeves, and bow to the threaded hole of the CNC winding machine directly above the wood core. Working principle The rotating shaft is a pair of rolling bearings fixed on the base to enlarge the bottom plate of the wooden core, and the net door is full of two meshes and two rotating parts.

The set screw, the threaded sleeve, the screw mounting block, the base fixing screw, the bearing shaft, and the base of the rotating shaft are coupled together. When the coil is freely rotated, the lead frame rotates together with the rotating shaft due to the pulling force of the wire, and passes through the wire. The wire of the wire sleeve on the frame is rotated to perform the payout. In addition to being used as a lock, the snail also acts as a shaft. There is a certain gap between the rotatable shape and the hole on the rotating shaft. Under the action of the pulling force of the wire, the shape will rotate in the counterclockwise direction indicated by the arrow on the arrow with the bolt as the rotating shaft, so as to be connected thereto. The lead frame will be slightly lifted, so that the stop screw on the lead frame is separated from the upper end panel of the wood core, so that it can be properly laid.

When the machine tool stops working, because the wire loses or reduces the pulling force, the lead frame falls under the action of its own gravity, so that the stop screw follows the falling and contacts the upper end panel of the wood core and rubs against it, in the role of friction. Next, stop the lead frame and stop the line. This pay-off frame is also very simple and convenient in terms of replacing the wire. Simply loosen and unscrew the nut on the bolt, remove the lead frame, and then loosen the fixing screw of the base to remove or replace the wood core. It is worth noting that the over-wire sleeve on the wire hole is preferably made of glazed ceramic to avoid scratching the skin of the wire and causing a short circuit of the wound coil. In addition, the lead frame should not be made too heavy, so that the tension of the wire is not enough to lift the wire frame, and the wire cannot be properly released.

(Finish)

Deutz Engine Part

Deutz engine part

Deutz engine part are widely used Agricultural Equipment, Construction Equipment , Marine Equipment , Material Handing, Stationary Equipment, Ground Support Equipment , Railway ,Automotive Diesel Engine , Deutz Provide power range from 25KW to 520 KW Water and cooler Engines

1. Germany Deutz Engine part

These part is Original /Genuine spare parts with Deutz Logo and Package , The Origin is Germany , Price is Expensive and have long delivery time .

2. Dalin Deutz Engine Part

Deutz ( Dalian ) Engine part is the same qulity of Germany parts, Many Detuz part is made in China , We can get these parts directly from manufacture with replacement for diesel engine .

3. Deutz Engine Parts number and Descriptions

Deutz Engine Cylinder block, cylinder liner , piston , piston ring , Pin, Lub oil cooler, Borgwarner Turbocharger , starter motor, alternator , Unit pump , Bosch Fuel injectors , lub oil pump , Repair kit Overhaul , Cylinder gasket , crankshaft, camshaft ,water pump ,Thermostat, Deutz ECU , Acutors, Aftercooler , Cylinder Head , Main Bearing ,Camshaft Bearing , Connect Rod and bearing , V-belts, Cam folloer,Push Rod, Flying wheel housing , Air compressor , Oil Pan , Radiator, Intake Valve, Exhaust Valve, Valve Spring, Valve Insert , Mann-Hummel Air filter, Fuel filter, Lub oil filter, Water filter.

Deutz diesel engine turbocharger

4. Deutz Engine Serize and Model

Deutz FL912/W, BFL913/C, B/FL413F/W; B/F513 series air-cooled diesel engine and BFL1011, BFM2011, BFM1012, BFM2012, BFM1013E/CP, BFM2013E/CP, BFM1015C TCD2011, TCD2012, TCD2013 series of water-cooled diesel engine and accessories.

Deutz Engine Part,Oil Cooler,Piston Ring,Diesel Engine Generator Spare Parts

Jining Kunpeng Construction Machinery Equipment Co., Ltd , https://www.excavatorenginepart.com